| You can fill in the blank to send your urgent purchasing info,so that the suppliers will get to you soon. Note: * are required! |
|
|
|
|
02MP106X More Information |
|
|
|
| Designed for use in solid state relays, MPU interface, TTL logic and any other light industrial or consumer application. Supplied in an inexpensive TOC92 package which is readily adaptable for use in automatic insertion equipment. • OneCPiece, InjectionCMolded Package • Blocking Voltage to 600 Volts • Sensitive Gate Triggering in Four Trigger Modes (Quadrants) for all possible Combinations of Trigger Sources, and especially for Circuits that Source Gate Drives • All Diffused and Glassivated Junctions for Maximum Uniformity of Parameters and Reliability • Improved Noise Immunity (dv/dt Minimum of 20 V/µsec at 110C) • Commutating di/dt of 1.6 Amps/msec at 110C • High Surge Current of 8 Amps • Device Marking: Device Type, e.g., for MAC997A6: MAC7A6, Date Code |
|
File Size:229613 KB
|
|
|
|
| Control input to the VCO. This voltage determines the output frequency and is derived from filtering the CPOUT voltage. Internal compensation node. This pin must be decoupled to ground with a 10nF capacitor. Internal compensation node. This pin must be decoupled to VVCO with a 10uF capacitor. VCO output. The output level is programmable from -6dBm to -13dBm. See Page 18 for a description of various output stages. VCO complementary output. The output level is programmable from -6dBm to -13dBm. See Page 18 for a description of various output stages. Charge Pump Ground. This is the ground return path for the charge pump. Digital Ground. Analog Ground. This is the ground return path of the prescaler & VCO. |
|
|
|
| • Because the clamp outputs carry DC, the clamp output traces routed to each AC coupled video output can be long. Avoid cutting a ground trace(s) simply to route clamp output traces and use wire jumpers, if necessary. • Clamp diodes (D3, D5, D6) and pull-up resistors (R20, R23, R24) should be placed closest to the video output traces to minimize the size of the video nodes and reduce parasitic capacitance on the video outputs. The clamp diodes must be 1SS83 or equivalent diodes; do not use 1N4148 type diodes. These diodes must have a fast transient response, low shunt capacitance, low series impedance, and a high peak current rating to clamp the video output voltage to the VCC supply during an arc event. • 0.1uF bypass capacitors (C46, C48, C9) should be placed very close to the 1SS83 type arc protection diodes (D1/D2, D4/D7, D8/D9) between VCC and ground. The ground connection should have a short, direct path to CRT ground. Therefore, arc currents shunted by the pro- tection diodes can return to the CRT DAG (J6). • 300V spark gaps (S1, S2, S3, S4) are strongly recom- mended and should be placed very close to the cathode and G1 pins and grounded directly to the CRT ground plane, so arc current can return to the nearby CRT DAG. Spark gaps help to minimize voltage stress on the CRT Driver and 02MP106X. • If the G1 blanking feature is used, all G1 circuit compo- nents should be placed as close as possible to the G1 pin of the CRT connector, with the exception of a small resistor (R2) placed close to the VBOUT pin to limit any current toward the 02MP106X. The sequence of circuit com- ponents from the VBOUT pin to the G1 pin is recom- mended to protect the 02MP106X against arcing. All these components must be grounded directly to the CRT ground plane. Therefore, arc currents can easily return to the CRT DAG. Do not omit any of the components in the G1 circuit as they are required to protect the 02MP106X against arcing and for correct G1 blank operation. • If the G1 blanking feature is not used, simply place a 470pF capacitor from the VBOUT pin to 02MP106X ground and do not connect the output to the G1 circuitry. Pin Options and No Connects • Depending on the pin options required, Pin 12 and Pin 13 can be connected to ground via a ground plane, trace, or jumper wire. See the Section Theory of Operation to determine the appropriate pin option for the application. • The No Connect or N/C pins (pins 16, 18, 20, 22, 24) are not connected to the die internally in order to achieve larger spacing between the high voltage VCC and VOUT pins. These N/C pins should not be used to route other traces through. |
|
| Parr number/PDF |
Mfg |
Pack |
D/C |
Descrpion |
Parr number/PDF |
Mfg |
Pack |
D/C |
Descrpion |
|
|
|
|
|
|
|
|
|
|
| 02M3003 |
|
|
|
³7KLV GRFXPHQW VWDWHV WK |
02M3027 |
|
|
|
configuration, the top surfa |
| 02MP142W |
NS |
SOP20W |
2007+ |
Notes: 1. Minimum Noise Figu |
02M3027 |
|
|
|
configuration, the top surfa |
| 02M3027 |
|
|
|
configuration, the top surfa |
02MM006 |
|
|
|
When decimating, the user sho |
|
